Assessment of compressive and flexural properties of three contemporary bulk fill resin composites

Authors

DOI:

https://doi.org/10.54589/38/3/237

Keywords:

compressive strength, composite resins, dental materials, flexural strength

Abstract

Contemporary restorative materials must demonstrate how much stress they can withstand before permanently deforming under the constant forces generated during chewing. Aim: To compare the compressive and flexural strength of three bulk fill resin composites. Materials and Method: This study analyzed three bulk fill resin composites: Opus™ bulk fill (OBF), Tetric® N-Ceram bulk fill (TNC), and Filtek™ bulk fill (FBF), and one conventional resin composite: Filtek™ Z350XT (FZXT) as a control group. Each composite was used to prepare 14 cylindrical specimens (n=56) for compressive strength tests, and 19 rectangular specimens (n=76) for flexural strength tests. Mechanical tests were performed using an Instron® universal testing machine - 100 kN load at a speed of 1 mm/1min. Results: Descriptive (Mean ± SD) and inferential statistics (Kruskal-Wallis test/ post-hoc test), p<0.05 were used. The compressive test results (Means ± SD) were: OBF (141.68MPa ± 22.20), TNC (139.03MPa ± 23.56), FBF (235.59MPa ± 26.08), and FZXT (99.28MPa ± 11.36). The flexural test results (Means ± SD) were: OBF (116.29 ± 7.20), TNCBF (109.67MPa ± 7.58), FBF (200.53MPa ± 10.32), and FZXT (90.08MPa ± 8.63). Statistically significant differences were found between the resin composites (p<0.001) in both mechanical tests. Conclusion: The bulk fill resin composites demonstrated higher compressive and flexural strength than the conventional resin composite. However, the use of these restorative materials may depend on specific clinical requirements and material handling preferences.

Downloads

Download data is not yet available.

Author Biographies

  • Norma Borja-Farfán, Universidad Peruana de Ciencias Aplicadas, Carrera de Odontología, Lima, Perú

    DDs, School of Dentistry, Universidad Peruana de Ciencias Aplicadas, Lima-Perú. 

    Second Specialization in Orthodontics and Maxillary Orthopedics,Universidad Peruana de Ciencias Aplicadas, Lima-Perú. 

  • Danilo Loyola-Livias, Universidad Peruana de Ciencias Aplicadas, Carrera de Odontología, Lima, Perú

    DDs, Lecturer in Dentistry, School of Dentistry, Universidad Peruana de Ciencias Aplicadas, Lima-Perú

    Second Specialization in Periodontics and Implantology, Universidad Peruana de Ciencias Aplicadas, Lima-Perú

  • Leslie Casas-Apayco, Universidad Peruana de Ciencias Aplicadas, Carrera de Odontología, Lima, Perú

    DDS  at Universidad San Martin de Porres, Lima-Perú

    MSc. in Dentistry,  Bauru School of dentistry, University of Sao Paulo, Brazil. 

    PhD. in  Dental Sciences, Bauru School of dentistry, University of Sao Paulo, Brazil. 

    Research Professor, School of Dentistry, Universidad Peruana de Ciencias Aplicadas, Lima-Perú. 

  • Monica Hermoza-Novoa, Universidad Peruana de Ciencias Aplicadas, Carrera de Odontología, Lima, Perú

    DDS  at Universidad San Martin de Porres, Lima-Perú

    MSc. in Dentistry, Bauru School of dentistry , University of Sao Paulo , Brazil. 

    Lecturer in Dentistry, School of Dentistry, Universidad Peruana de Ciencias Aplicadas, Lima-Perú

Downloads

Published

2025-12-31

Issue

Section

Artículos originales

How to Cite

Assessment of compressive and flexural properties of three contemporary bulk fill resin composites. (2025). Acta Odontológica Latinoamericana, 38(3), 237-241. https://doi.org/10.54589/38/3/237